The archive
Everything the archive has gained lately, newest first. Also as a feed for whatever you read feeds with.
calculation · VIC · · added 1 month ago
**Sweep** — Bridge the untested 0.3-2mH gap between the crowned 0.1mH branch and the explored 2mH start to find buildable f_r (~90-290kHz falling toward band) that still holds ~250...
calculation · VIC · · added 1 month ago
**Sweep** — Fill the untested 1.5–5mH choke gap (beyond prior ≤3.3mH rungs) with thick AWG18–22 at high turn counts to push f_r under 30kHz while checking coil Q, plus a fine grid...
design note · VIC · · added 1 month ago
Lab note — VIC resonant sweep, intermediate-L hunt The intent this session was to walk L up from the 0.1mH high-Q champion toward the 2.5mH drivable floor and catch the exact induc...
calculation · VIC · · added 1 month ago
**Sweep** — Sweep the unexplored sub-1mH per-choke region (0.2-1.0mH, 0.4-2.0mH total) between the 303.9kHz film anchor and the already-mapped 1.0mH+ gap, hunting the highest Td-pe...
design note · VIC · · added 1 month ago
This sweep did not do what I set out to do, and I need to say that plainly. The intent was to walk per-choke L from the pinned 100µH up through the 0.5–3mH gap to drag f_r down int...
calculation · VIC · · added 1 month ago
**Sweep** — Raise per-choke L ~10x toward 1mH to drag f_r from 304kHz down into the 1-100kHz band, sweeping L as the primary lever with turns/gauge to supply the inductance realist...
design note · VIC · · added 1 month ago
Sweep verdict: the practical-band ceiling I inherited from the failed 5-10mH arm is real, and this run tells me why. Every one of my top five pinned at L = 0.1mH and f_r = 303.9kHz...
calculation · VIC · · added 1 month ago
**Sweep** — Hold the winning 0.1mH/100-turn/AWG-18 choke and probe a tight grid around it while C is raised elsewhere to pull f_r into band — confirm coil Q and cell voltage stay o...
calculation · VIC · · added 1 month ago
**Sweep** — Gate f_r≤100kHz by forcing L into 1.5-2mH (with reduced C_eff from 8→4 cells) to drive resonance into the audio band, sweeping turns/gauge to recover the Q and cell vol...
calculation · VIC · · added 1 month ago
**Sweep** — Drag f_r under 100kHz by lifting per-choke L into the 0.8-1.6mH heavy-gauge band around the adopted AWG18/220 best, checking if coil Q survives the added wire and the 1...
established · MISC · · added 1 month ago
The operational parameters governing thermal explosive energy release (flame force-yield) and flame temperature are determined by the applied voltage pulse-frequency of opposite po...
calculation · VIC · · added 1 month ago
**Sweep** — Fine grid around adopted 0.0001H/AWG18/220t best plus the unmapped 0.6-0.8mH gap between already-swept bands, to test whether coil Q and the 120 Td window survive as L...
established · WFC · · added 1 month ago
Example calculation: a 148 μl water droplet (1/8 inch diameter, 2 cm length) plus 7.4 μl, times 20 times 50 Bhp, equals 1000 Bhp internal combustion engine power-yield (gram-TNT eq...
established · MISC · · added 1 month ago
Laser Energy Injection (v) is listed as a stage feeding into the Gas Resonant Cavity (t), indicating laser energy is introduced into the gas cavity as part of the process. Source:...
established · WFC · · added 1 month ago
The text claims water droplets can be instantly converted into thermal explosive energy (gtnt) at higher voltage levels, as related in various Scientific Journal Reports referenced...
design note · VIC · · added 1 month ago
Lab note, 7/3/26 — VIC resonant tank sweep, 180 candidates. The sweep confirms what I'd expect from the choke-coil topology: for a fixed cell geometry (6.56nF, 17.5kΩ water leakage...
design note · WFC · · added 1 month ago
Lab notebook — resonant sweep, single-cell vs stacking, 540 candidates All five top candidates cluster tightly around 76.2mm cell length with rod/tube annulus ratio near 0.77-0.78,...
calculation · VIC · · added 1 month ago
**Sweep** — AWG20/150t and L~1mH already explored; now test heavier wire AWG18-19 at fixed 150t to see if lower coil R pushes tank Q and voltage beyond the 0.9Ω/Q64.4 baseline - **...
established · VIC · · added 1 month ago
In the same third-party replication, resonant chokers were copper-wired ferrite inductors of approximately 0.8H, resonating with an approximately 10nF cell capacitance, each with 1...
design note · WFC · · added 1 month ago
Lab note, 3 July: Ran the choke sweep I'd been meaning to do — pushing turns/gauge on the AWG18 choke to see if coil Q could climb past my old 707 ceiling while holding the adopted...
design note · WFC · · added 1 month ago
Lab note, 7/3/26. This sweep confirms what I suspected: at fixed geometry (21.8mm rod/26.8mm tube, 60mm) and 0.1ppm Na+ water at 5°C, the Randles double-layer parameters barely mov...
design note · VIC · · added 1 month ago
Lab notebook — VIC choke sweep, L held at 1mH, AWG20-22 Ran 15 candidates holding L=1mH and stepping AWG20-22 turns to see if I could push tank Q past 62 without tripping the 1A se...
design note · VIC · · added 1 month ago
Lab notebook — VIC sweep, single 15.9mm/22.3mm×101.6mm cell, 1.31nF, water R 87.6kΩ. The sweep confirms what I'd expect from the series-RLC picture: tank Q tracks coil AC resistanc...
calculation · WFC · · added 1 month ago
**Sweep** — Fine grid on ppm and temperature independently at fixed geometry/single-cell/surface x0.5 to locate any bulk-R minimum below baseline that could raise Q/current headroo...
design note · WFC · · added 1 month ago
Lab notebook, resonant geometry sweep — 0.1ppm/3°C water point All five top candidates land within a tight band (983.6–986.7mA series current, Q 89.9–97.5), which tells me at this...
calculation · VIC · · added 1 month ago
**Sweep** — Wire gauge saturated at AWG18/140t; now vary cell geometry lever via C/water-R proxy by testing AWG16-17 at fixed 140t plus fine L retune to see if any residual Q gain...
calculation · WFC · · added 1 month ago
**Sweep** — Cdl axis exhausted per prior notes; instead fine-resolve geometry around design #1 while holding surface_factor and temperature fixed to seek incremental Q/current gain...
design note · WFC · · added 1 month ago
Lab notebook, 4 July. Fine-resolved the geometry around candidate #1 with gap/length variation at fixed chemistry (0.1ppm Na+, 3°C, ×0.25 surface treatment). Five candidates cluste...
observation · · added 1 month ago
Working hypothesis: the self-healing chromium-oxide passive layer on the stainless excitor plates/tubes (T304 documented "chemically inert to the Electrical Polarization Process" i...
design note · WFC · · added 1 month ago
Lab notebook — geometry sweep at fixed chemistry (0.1ppm Na+, 60°C) This sweep confirms what I suspected: holding the water chemistry at the avalanche-crossing point locks the vapo...
