Skip to content
Stan’s Legacy The Stanley Meyer Archive
Sign in

The archive

What’s new

Everything the archive has gained lately, newest first. Also as a feed for whatever you read feeds with.

13,573 items

August 2026

  • document · · added 2 months ago

    Primary Side

    Primary Side (L1-C1) Analysis The primary side of the VIC consists of the first inductor (L1) and tuning capacitor (C1). This stage receives the driving signal and provides the fir...

  • document · · added 2 months ago

    VIC Introduction

    What is a VIC Circuit? The Voltage Intensifier Circuit (VIC) is a resonant circuit topology designed to develop high voltages across a water fuel cell (WFC) while drawing relativel...

  • document · · added 2 months ago

    Calculator Overview

    VIC Matrix Calculator Overview The VIC Matrix Calculator is a comprehensive design tool that integrates all the concepts covered in this educational series. It allows you to design...

  • document · · added 2 months ago

    Component Inputs

    Component Input Parameters This page details all input parameters used across the VIC Matrix Calculator modules. Understanding what each parameter means and how to determine its va...

  • document · · added 2 months ago

    10XA Analysis

    This page will continually be updated as more information is gathered, please check back regularly YouTube videos: How To Make A 10XA Alternator 10XA Drive Motor Variable Speed Dri...

  • document · · added 2 months ago

    .STEP and STLs

    The following .STEP and STL files are from Memo WFC 423-DA. The .STEP files have been provided for CNC machining. STLs are for 3D printing. Discrepancies were found with Stan's ori...

  • document · · added 2 months ago

    2000 Permeability EC52 core

    The following test results were performed using a 2000 permeability EC52/24/14 core purchased from Mouser Electronics. Please see the link below for the exact core. Mouser Electron...

  • document · · added 2 months ago

    Stan Meyer Machining Template STLs_5-22-2024

    Please be aware that new templates will be added when DIY machining techniques are tested. Check regularly until this banner is removed - indicating the below listed have been fina...

  • document · · added 2 months ago

    Hydrogen Gas Gun - 3D STLs

    As of 5-2-23, the below STLs are currently being printed and tested. It is recommended until verification of the parts is completed, that the content herein should be for informati...

  • document · · added 2 months ago

    Photon Injected Resonant Cavity - 3D STLs

    Stan had a "triple stack" which was composed of three individual resonant cavities stacked on top one another. These were large and made of machined Delrin. At the top of each was...

  • document · · added 2 months ago

    4200 Permeability EC52 E Core

    The following test results were performed using a 4200 permeability EC52/24/14 core purchased from Surplus Sales. Please see the link below for the exact core. Surplus_Sales_4200_E...

  • document · · added 2 months ago

    04-29-1976

    Page 1 Page 5

  • document · · added 2 months ago

    EPG Speculations/Suggestions

    *** Page will be continually updated. Highlighted below, appears to be various, thick varnishing applied to outer surface of copper tubing on each EPG model. Figure 3 demonstrates...

  • document · · added 2 months ago

    Resonant Cavity - 3D STLs

    Author does not accept and liabilities/responsibilities for those individuals who chose to build the below cell. This information on this site is for educational purposes only. Cav...

  • document · · added 2 months ago

    07-29-1976

    Page 1 Page 16

  • document · · added 2 months ago

    Coil Winder For VIC5

    End cap for holding VIC5 bobbin. Bottom has hexagonal recess for 5/16" nylon lock nut. Best method is to lay flat, line up nut flat edges and lightly tap with hammer flush into rec...

  • document · · added 2 months ago

    Steam Resonator - 3D STLs

    As of 5-3-23 the STLs shown in here are being printed to build a plastic model. At this point, please only consider the following as informational and do not print until all parts...

  • document · · added 2 months ago

    03-18-1976

    Page 1 Page 5

  • document · · added 2 months ago

    The Path to Water Fuel Cells

    Stanley Meyer's journey towards developing water fuel cell technology was driven by his desire to find an alternative to the world's dependence on fossil fuels. During the 1970s, a...

  • book · · added 2 months ago

    Electromagnetic Theory, Vol. 1 (1893) — part 23 of 31

    Heaviside developed operational calculus (Laplace transforms before Laplace) and transmission line theory. This volume covers electromagnetic wave propagation, energy transfer, imp...

  • book · · added 2 months ago

    Electromagnetic Theory, Vol. 2 (1899) — part 1 of 31

    Continues the development of electromagnetic theory with focus on wave propagation in dispersive media, skin effect, and energy flow in electromagnetic systems. Relevant to VIC res...

  • book · added 2 months ago

    Kanarev - Hydrogen Generator

    This document is about Phillip Kanarev's work, NOT Stanley Meyer's. It is included as related research.

  • book · · added 2 months ago

    Electromagnetic Theory, Vol. 1 (1893) — part 24 of 31

    Heaviside developed operational calculus (Laplace transforms before Laplace) and transmission line theory. This volume covers electromagnetic wave propagation, energy transfer, imp...