Search Results

There are 2 inductors on a ferrite core, closed loop U shape. The core's permeability is approx 2000. One coil is 300 turns of 22Ga wire, and the other coil is 1000 turns of 30Ga wire. The inductance of the 300 turn coil, while shorting the 1000 turn coil, i...

Stan had a "triple stack" which was composed of three individual resonant cavities stacked on top one another. These were large and made of machined Delrin. At the top of each was a circular PCB composed of 5mm 660nm LEDs. 660nm LEDs were seen throughout Meyer...

  There seems to be a BIG PROBLEM with the assumptions being made about the dimensions of the tube sets and everyone needs to understand this because the absolutely critical gap between cathode and anode is different in each of the following 3 information s...

Detailed scientific explanations of the electrolysis of water is detailed below and the electric effects on water, magnetic effects on water, electromagnetic effects on water and the water redox process can all be accessed using the links immediately below: - ...

Steam resonator: the different polarity firing sequences across the parallel plates (or could be concentric tubes) are as follows:  Polarity firing sequence 1 for a pair of plates: WFC Hydrogen Gas Management System Memo WFC 422DA page 3-25 and diagram 3-46 o...

If you're looking to orient water molecules in an electric field, a relatively modest electric field can achieve this because water is a polar molecule. To align a water molecule, an electric field on the order of 1 kV/cm is often more than enough. Given a 1/8...

As of 5-3-23 the STLs shown in here are being printed to build a plastic model. At this point, please only consider the following as informational and do not print until all parts are verified to be correct. TOP CAP: Top cap is as the name implies. Screw h...

As of 5-18-23, STLs are being printed to test assembly. At this time, until this banner is removed, please do not attempt printing. Verification is needed before others waste time and resources for parts that don't go together. Thank you. RETAINING CAP: (100...

As of 5-2-23, the below STLs are currently being printed and tested. It is recommended until verification of the parts is completed, that the content herein should be for information only.  Estate photographs were used in conjunction with a pair of calipers. ...

As of 5-2-23, the below STLs are currently being printed and tested. It is recommended until verification of the parts is completed, that the content herein should be for information only.  Estate photographs were used in conjunction with a pair of calipers. ...

Estate photographs were used in conjunction with a pair of calipers. Screen was adjusted until a common reference point was ascertained. The reference point used was the known dimensions of the LED PCB width, being 1.00". Length was determined by laying out th...

Steam Resonator_Outer Electrode.pdf Steam Resonator_SR Block.pdf Steam Resonator_Stem Plate.pdf Steam Resonator_Top Cap.pdf Steam Resonator_Delrin Nut.pdf Steam Resonator_Inner Electrode.pdf Steam Resonator_End Cap.pdf Steam Resonator_Insulator Block.pd...

Photon Resonant Cavity_Inner Electrode.pdf Photon Resonant Cavity_LED Groove Stencil.pdf Photon Resonant Cavity_Outer Electrode.pdf Photon Resonant Cavity_Acrylic Lens.pdf Photon Resonant Cavity_Body 1.pdf Photon Resonant Cavity_Body 2.pdf  

RETAINING CAP: (100% Fill: 65G) , (50% Fill: 45G) Retaining Cap.stl UPPER INTAKE: (100% Fill: 29G) , (50% Fill: 23G) Upper Intake.stl BOTTOM PIECE OF UPPER INTAKE: (100% Fill: 2G) , (50% Fill: 2G) Bottom Piece To Upper Intake.stl TOP O-RING (...

Installing and Using the ESP32 Complex Waveform Generator V3 Application Screenshot of web interface Prerequisites To use this application, you need to have the Arduino IDE installed on your computer. You can download the Arduino IDE from the official...

As of 5-3-23 the STLs shown in here are being printed to build a plastic model. At this point, please only consider the following as informational and do not print until all parts are verified to be correct. TOP CAP: Top cap is as the name implies. Screw h...

Stan had a "triple stack" which was composed of three individual resonant cavities stacked on top one another. These were large and made of machined Delrin. At the top of each was a circular PCB composed of 5mm 660nm LEDs. 660nm LEDs were seen throughout Meyer...