Search Results

As of 5-2-23, the below STLs are currently being printed and tested. It is recommended until verification of the parts is completed, that the content herein should be for information only.  Estate photographs were used in conjunction with a pair of calipers. ...

As of 5-18-23, STLs are being printed to test assembly. At this time, until this banner is removed, please do not attempt printing. Verification is needed before others waste time and resources for parts that don't go together. Thank you. RETAINING CAP: (100...

Stan had a "triple stack" which was composed of three individual resonant cavities stacked on top one another. These were large and made of machined Delrin. At the top of each was a circular PCB composed of 5mm 660nm LEDs. 660nm LEDs were seen throughout Meyer...

As of 5-3-23 the STLs shown in here are being printed to build a plastic model. At this point, please only consider the following as informational and do not print until all parts are verified to be correct. TOP CAP: Top cap is as the name implies. Screw h...

If you're looking to orient water molecules in an electric field, a relatively modest electric field can achieve this because water is a polar molecule. To align a water molecule, an electric field on the order of 1 kV/cm is often more than enough. Given a 1/8...

Steam resonator: the different polarity firing sequences across the parallel plates (or could be concentric tubes) are as follows:  Polarity firing sequence 1 for a pair of plates: WFC Hydrogen Gas Management System Memo WFC 422DA page 3-25 and diagram 3-46 o...

Detailed scientific explanations of the electrolysis of water is detailed below and the electric effects on water, magnetic effects on water, electromagnetic effects on water and the water redox process can all be accessed using the links immediately below: - ...

  There seems to be a BIG PROBLEM with the assumptions being made about the dimensions of the tube sets and everyone needs to understand this because the absolutely critical gap between cathode and anode is different in each of the following 3 information s...

here is a replication of stan meyer's spherical resonant cavity. outer sphere is 3 inch diameter 11ga 304l stainless steel, inner sphere is a 1inch 304l solid ball. a centering jig was 3d printed to use the pre-drilled hole in the outer sphere as a referen...

Energy of the Future Raum & Zeit Vol 1. No. 6. 1990 R&Z HFP_Page1.pdf , R&Z HFP_Page10.pdf , R&Z HFP_Page2.pdf , R&Z HFP_Page3.pdf , R&Z HFP_Page5.pdf , R&Z HFP_Page4.pdf , R&Z HFP_Page7.pdf , R&Z HFP_Page6.pdf , R&Z HFP_Page8.pdf , R&Z HFP_Page9.pdf  Hyd...

VIC Inner Core Bobbin .stl VIC Outer Core Bobbin .stl

GPT Interpretation from: https://stanslegacy.com/books/us-patents/page/gas-generator-voltage-control-circuit-4798661 L-1. Voltage and Current Regulation: The use of a uni-polar pulsating DC voltage is an initial approach to raise the amplitude of the voltage ...

Amp Restriction in the VIC Variable Pulse Voltage Frequency: Adjust the pulse voltage frequency to keep amp flow minimal, crucial for efficient operation. Expanded: This stage is essential for maintaining energy efficiency, where the pulse frequency is fin...

The "9 Stages to Voltage Attenuation" of the VIC Conventional Power Supply - less than 1V - 110V DC (or equivalent rectified AC) TBD - no mention (believed to be the Gate Frequency & Process) Pulse Train concentrated or "Time-regulated" variable pulse vol...

These replicated cavities are the ones used on the buggy. Some machining is required for the inner electrodes, cost effectiveness may not be ideal for many experimenters. Therefore, a 3D printable and glue-together template was made to allow those with simple ...